I've used Pi's since as soon as I could buy them but I've never run one
24/7 before so I'd like to ensure I've done sufficient to maximise SD
Card life.

All this PI does is sit accepting SSH connections and acts as a gateway
to allow tunnelling or SOCKS5 proxying. It also lets me send WOL magic
packets to other local computers to wake them up so I don't need to
leave those computers running 24/7. That's all working fine.

However, I'd like to maximise the SC Card life where possible so I have
mounted a few places onto tmpfs to minimise writes to the card. I have a
couple of cron jobs running that tickle the dynamic DNS provider and
another that reboots the Pi every 24 hours as a crude and simple way of ensuring not the tmpfs log space doesn't fill.

The following are mounted onto tmpfs:

tmpfs on /tmp type tmpfs (rw,nosuid,noatime,size=102400k)
tmpfs on /var/spool/mqueue type tmpfs (rw,nosuid,noatime,size=30720k,mode=700,gid=12)
tmpfs on /var/tmp type tmpfs (rw,nosuid,noatime,size=30720k)
tmpfs on /var/log type tmpfs (rw,nosuid,noatime,size=102400k,mode=755)

There is no swap running as all this does is SSH connection handling.

I have plenty of old small (8Gb) SD Cards to replace the one in use but
I don't want to have to be copying a new one more often than needed.

Is there anything else that really needs doing or is this sufficient?

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 20/03/2021 11:22 am, mm0fmf wrote:

I've used Pi's since as soon as I could buy them but I've never run one
24/7 before so I'd like to ensure I've done sufficient to maximise SD
Card life.

All this PI does is sit accepting SSH connections and acts as a gateway
to allow tunnelling or SOCKS5 proxying. It also lets me send WOL magic packets to other local computers to wake them up so I don't need to
leave those computers running 24/7. That's all working fine.

However, I'd like to maximise the SC Card life where possible so I have mounted a few places onto tmpfs to minimise writes to the card. I have a couple of cron jobs running that tickle the dynamic DNS provider and
another that reboots the Pi every 24 hours as a crude and simple way of ensuring not the tmpfs log space doesn't fill.

The following are mounted onto tmpfs:

tmpfs on /tmp type tmpfs (rw,nosuid,noatime,size=102400k)
tmpfs on /var/spool/mqueue type tmpfs (rw,nosuid,noatime,size=30720k,mode=700,gid=12)
tmpfs on /var/tmp type tmpfs (rw,nosuid,noatime,size=30720k)
tmpfs on /var/log type tmpfs (rw,nosuid,noatime,size=102400k,mode=755)

There is no swap running as all this does is SSH connection handling.

I have plenty of old small (8Gb) SD Cards to replace the one in use but
I don't want to have to be copying a new one more often than needed.

Is there anything else that really needs doing or is this sufficient?

If you can, put the root filesystem on a USB connected thumbdrive or SSD.


--
Chris Elvidge
England

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 19.3.21 23.03, Craig Dooley wrote:

BY: mm0fmf(3:770/3)

I've used Pi's since as soon as I could buy them but I've never run one 24/7 before so I'd like to ensure I've done sufficient to maximise SD
Card life.

Not sure what Pi you have, but if it's a 4, have you thought about going with USB instead of SD card? I've currently got my BBS running on a RPi 4 with everything on a USB drive. 128 GB flash drive the size of my thumbnail plugged
into one of the USB 3.0 ports. Works fine, and I don't have to worry about read/write cycles.

-Craig

I'm just curious: What makes a Flash memory on an USB interface
more durable than a Flash memory on a SD card?

--

-TV

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 19/03/2021 21:03, Craig Dooley wrote:

BY: mm0fmf(3:770/3)

I've used Pi's since as soon as I could buy them but I've never run one 24/7 before so I'd like to ensure I've done sufficient to maximise SD
Card life.

Not sure what Pi you have, but if it's a 4, have you thought about going with USB instead of SD card? I've currently got my BBS running on a RPi 4 with everything on a USB drive. 128 GB flash drive the size of my thumbnail plugged
into one of the USB 3.0 ports. Works fine, and I don't have to worry about read/write cycles.

-Craig

I meant to say it's a Pi Zero W but forgot.

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 2021-03-19, Craig Dooley <nospam.Craig.Dooley@f126.n123.z1.fidonet.org> wrote:

BY: mm0fmf(3:770/3)

I've used Pi's since as soon as I could buy them but I've never run one 24/7 before so I'd like to ensure I've done sufficient to maximise SD
Card life.

Not sure what Pi you have, but if it's a 4, have you thought about going with USB instead of SD card? I've currently got my BBS running on a RPi 4 with everything on a USB drive. 128 GB flash drive the size of my thumbnail plugged
into one of the USB 3.0 ports. Works fine, and I don't have to worry about read/write cycles.

It's flash whether the interface is SD or USB - there is a write limit!

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 20/03/2021 14:29, Tauno Voipio wrote:

On 19.3.21 23.03, Craig Dooley wrote:

BY: mm0fmf(3:770/3)

I've used Pi's since as soon as I could buy them but I've never run

one

24/7 before so I'd like to ensure I've done sufficient to maximise SD
Card life.

Not sure what Pi you have, but if it's a 4, have you thought about
going with
USB instead of SD card?  I've currently got my BBS running on a RPi 4
with
everything on a USB drive.  128 GB flash drive the size of my
thumbnail plugged
into one of the USB 3.0 ports.  Works fine, and I don't have to worry
about
read/write cycles.

-Craig

I'm just curious: What makes a Flash memory on an USB interface
more durable than a Flash memory on a SD card?

I don't know.

My day job is writing semiconductor models (think QEMU-like). We've
done loads of NAND, NOR, UFS, eMMC, SdCard/MMC device and controllers, MobileStorage, NVMe models for our customers with varying levels of
realism. Our customers have never been keen to discuss wear levelling,
it's considered commercially confidential by them and isn't released
even under NDA.

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On Sat, 20 Mar 2021 16:29:04 +0200
Tauno Voipio <tauno.voipio@notused.fi.invalid> wrote:

I'm just curious: What makes a Flash memory on an USB interface
more durable than a Flash memory on a SD card?

Nothing in principle, except the quality and type of the flash
memory (there are a lot of types) and the on-board controller. All flash
memory (including SLC SSDs) are subject to write wear due to the mechanism
and write amplification due to large block sizes - how quickly they wear depends on the flash technology used, the sophistication of the controller (wear levelling, TRIM etc) and the quality of manufacture. Micro SD cards
tend to be towards the bottom end of everything - NVMe SSDs sold for data centre use tend to be towards the top.

USB sticks are very variable IME but the good ones are a lot better than any micro SD card.

--
Steve O'Hara-Smith | Directable Mirror Arrays C:\>WIN | A better way to focus the sun
The computer obeys and wins. | licences available see
You lose and Bill collects. | http://www.sohara.org/

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On Sat, 20 Mar 2021 16:04:32 +0000, Jim Jackson wrote:

On 2021-03-19, Craig Dooley
<nospam.Craig.Dooley@f126.n123.z1.fidonet.org> wrote:

BY: mm0fmf(3:770/3)

I've used Pi's since as soon as I could buy them but I've never run

one m> 24/7 before so I'd like to ensure I've done sufficient to
maximise SD m> Card life.

Not sure what Pi you have, but if it's a 4, have you thought about
going with USB instead of SD card? I've currently got my BBS running
on a RPi 4 with everything on a USB drive. 128 GB flash drive the size
of my thumbnail plugged into one of the USB 3.0 ports. Works fine, and
I don't have to worry about read/write cycles.

It's flash whether the interface is SD or USB - there is a write limit!

IIRC the on-device controller on any type of SSD is a lot smarter than
the ones fitted to a built-down-to-price semi-disposable SD card, and one
place this shows up is in dealing with card wear, i.e EEPROM ageing
defects. I don't think any SD card can remove a bad memory page from the
active pages map and replace it with one of the spares - something most
SSDs can do - because for starters SD memory pages are relatively large
(4Kb?) and pricing says they don't have any list of spare pages or a
controller that could handle remapping.

I'm told that the better (enterprise grade) SSDs will drop into read-only
mode when they find a prefefined unfixable number of defects. This means
the data content can be retrieved without errors. Lower spec SSDs and all
SD cards will merrily go on writing data well past that point.

--
Martin | martin at
Gregorie | gregorie dot org

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On Sat, 20 Mar 2021 11:42:38 +1300, Craig Dooley wrote:

BY: Tauno Voipio(3:770/3)

I'm just curious: What makes a Flash memory on an USB interface TV>

more durable than a Flash memory on a SD card?

I'm not really sure. it's my understanding that SD cards will wear out because of read/write cycles eventually. I've never heard that said of
a USB flashdrive. But I'm not an expert on either.

SSDs wear out too - eventually - just the same as an HDD. The difference
is that SSDs data pages (a) survive many more read/zero/write cycles than
those in SD cards and (b) have a set of spare data pages that can be
remapped to replace failing ones. Cheap as chips SD cards don't do this
either.


--
Martin | martin at
Gregorie | gregorie dot org

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On Sat, 20 Mar 2021 20:47:39 -0000 (UTC)
Nikolaj Lazic <nlazicBEZ_OVOGA@mudrac.ffzg.hr> wrote:

Dana Sat, 20 Mar 2021 11:42:38 +1300, Craig Dooley <nospam.Craig.Dooley@f126.n123.z1.fidonet.org> napis'o:

BY: Tauno Voipio(3:770/3)

I'm just curious: What makes a Flash memory on an USB interface
more durable than a Flash memory on a SD card?

I'm not really sure. it's my understanding that SD cards will wear out because
of read/write cycles eventually. I've never heard that said of a USB
flashdrive. But I'm not an expert on either.

I've got few of USB flash drives that died. Or got read only.

I haven't got a singe failed one, and my oldest (still in use) is a massive 128M - from the days when that was the biggest you could get!

I particularly like that it has a mechanical write protect switch and slim
but tough case. I can't tell you the make - all the writing has long since worn away!

--
W J G

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

Dana Sat, 20 Mar 2021 11:42:38 +1300, Craig Dooley <nospam.Craig.Dooley@f126.n123.z1.fidonet.org> napis'o:

BY: Tauno Voipio(3:770/3)

I'm just curious: What makes a Flash memory on an USB interface
more durable than a Flash memory on a SD card?

I'm not really sure. it's my understanding that SD cards will wear out because
of read/write cycles eventually. I've never heard that said of a USB flashdrive. But I'm not an expert on either.

I've got few of USB flash drives that died. Or got read only.

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 20/03/2021 11:35, Jim Jackson wrote:

It sounds like you usage is a fit for running with the root file system readonly

Thanks. I found an article from 2016 about making root read only FS for
a Pi. I'll give that a test run tomorrow and see how it goes.

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

mm0fmf <none@invalid.com> wrote:

On 20/03/2021 11:35, Jim Jackson wrote:

It sounds like you usage is a fit for running with the root file system
readonly

Thanks. I found an article from 2016 about making root read only FS for
a Pi. I'll give that a test run tomorrow and see how it goes.

The "PiCore" version of Tiny Core Linux runs on the Pi with the core
system entirely in RAM. It should be possible to have that boot from
a read-only partition, though it might be easiest to remount it
read-only after booting to avoid modifying the boot scripts.

By remastering PiCore with all your required software "built-in" it
would be possible to run everything in RAM and unmount the SD card
entirely after boot.

--
__ __
#_ < |\| |< _#

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 20/03/2021 14:28, mm0fmf wrote:

On 19/03/2021 21:03, Craig Dooley wrote:

BY: mm0fmf(3:770/3)

I've used Pi's since as soon as I could buy them but I've never run

one

24/7 before so I'd like to ensure I've done sufficient to maximise SD
Card life.

Not sure what Pi you have, but if it's a 4, have you thought about
going with
USB instead of SD card?  I've currently got my BBS running on a RPi 4
with
everything on a USB drive.  128 GB flash drive the size of my
thumbnail plugged
into one of the USB 3.0 ports.  Works fine, and I don't have to worry
about
read/write cycles.

-Craig

I meant to say it's a Pi Zero W but forgot.

I wouldn't worry about it.
I have 10 Pi zeros working 24/7 as CCTV cameras.
Each day they record between 1-5GB of new images recovering space by
removing images that are a few days old.
The SD cards (32GB) wear out every 3 or 4 years.

--
Nev
It causes me a great deal of regret and remorse
that so many people are unable to understand what I write.

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)